Practise › Questions › Heat engines and heat pumps
Heat engines and heat pumps questions
Why no engine, however perfect its engineering, can turn all its heat into work, and how the same machine run backwards heats your house with more energy than you feed it. A p-V diagram gives the work done per cycle, and comparing the theoretical loop with the measured one shows how real-engine losses reduce the output.
17 original questions · 51 marks · the heat engines and heat pumps notes · Engineering physics
On this topic the library is tagged for AQA.
Every question here is written for this library rather than taken from a past paper. Write your answer out before opening a mark scheme: the schemes award marks point by point, and the marks are easier to see when you have something of your own to compare against.
State the energy transfers that take place in one cycle of a heat engine, and write an equation for the work done per cycle.
Mark scheme
Each cycle the working substance absorbs heat QH from a hot source, converts part of it to useful work W, and rejects the rest, QC, to a cold sink (1). Energy is conserved, so W = QH − QC (1).Explain why no heat engine can be 100% efficient, even if all friction could be removed.
Mark scheme
The working substance must be returned to its starting state to repeat the cycle, which means compressing it, and that requires heat QC to be rejected to a colder sink (1). Since QC can never be zero, W = QH − QC is always less than QH, so the efficiency is always below 1 (1).Write the equation for the maximum theoretical efficiency of a heat engine, and state the temperature scale that must be used in it.
Mark scheme
Maximum theoretical efficiency = (TH − TC)/TH (1), where TH and TC are the source and sink temperatures in kelvin (1). It is a ratio of absolute temperatures, so a celsius value anywhere in it voids the answer.Define the coefficient of performance of a refrigerator and of a heat pump.
Mark scheme
Refrigerator: COP = QC/W, the heat removed from the cold space per unit of work input (1). Heat pump: COP = QH/W, the heat delivered to the hot space per unit of work input (1). Each is a benefit divided by the work paid for, and each is a pure number, not a percentage.State how the net work done per cycle by an engine is found from its loop on a p-V diagram, and state the direction in which an engine traverses the loop.
Mark scheme
The net work per cycle is the area enclosed by the loop (1), and an engine goes round it clockwise, expanding at high pressure and compressing at low pressure so that more work comes out than goes back in (1).State how the input power of an engine is calculated from its fuel.
Mark scheme
Input power = calorific value of the fuel × the rate at which fuel is burned (1), in J kg−1 × kg s−1 to give watts.In each cycle an engine absorbs 1500 J of heat from its source and rejects 1050 J to its sink. Calculate the work done per cycle and the efficiency of the engine.
Mark scheme
W = QH − QC = 1500 − 1050 = 450 J (1). Efficiency = W/QH (1) = 450/1500 = 0.30, that is 30% (1). Dividing W by QC instead of QH is the standard slip; the denominator is always what went in.An engine takes in heat from a source at 520 °C and rejects heat to a sink at 30 °C. Calculate its maximum theoretical efficiency.
Mark scheme
Convert to kelvin first: TH = 520 + 273 = 793 K and TC = 30 + 273 = 303 K (1). Maximum efficiency = (TH − TC)/TH (1) = (793 − 303)/793 = 0.62, about 62% (1). Working in celsius gives 0.94, wildly too high, and is the single most common error in this topic.A four-cylinder engine runs at 30 cycles per second and the p-V loop for each cylinder encloses an area of 260 J. Calculate the indicated power of the engine.
The crankshaft of an engine delivers a torque of 145 N m at 3600 revolutions per minute. Calculate the brake power.
An engine burns fuel of calorific value 43 MJ kg−1 at a rate of 3.5 × 10−3 kg s−1 and delivers a brake power of 52 kW. Calculate the input power and the overall efficiency.
In each cycle a refrigerator extracts 250 J of heat from its cold compartment using 100 J of work. Calculate its coefficient of performance and the heat rejected into the kitchen per cycle.
A heat pump with a coefficient of performance of 3.6 delivers heat to a house at 7.2 kW. Calculate the electrical power it consumes and the rate at which it extracts heat from the outside air.
A six-cylinder engine burns fuel of calorific value 45 MJ kg−1 at 4.0 × 10−3 kg s−1. Each cylinder's p-V loop encloses 480 J and the engine completes 25 cycles per second. The output shaft turns at 2900 revolutions per minute and delivers a torque of 210 N m. Calculate the input power, the indicated power, the brake power, the friction power and the overall efficiency.
In each cycle an engine absorbs 2400 J of heat from a source at 900 K and rejects 1560 J to a sink at 320 K, completing 20 cycles per second. Calculate the work per cycle, the output power, the actual efficiency and the maximum theoretical efficiency, and comment on the comparison.
A householder can heat a room either with a 3.0 kW electric heater or with a heat pump of coefficient of performance 4.0 drawing the same 3.0 kW of electrical power. Calculate the heating power delivered by each, and explain why the heat pump does not break conservation of energy.
A refrigerator has a coefficient of performance of 2.4 and its compressor draws 90 W of electrical power. Calculate the rate at which heat is removed from the cold compartment and the rate at which heat is delivered to the kitchen, and explain why running the refrigerator with its door left open warms the kitchen rather than cooling it.
The same practice on paper: the printable workbook for this topic, questions and a worked answer book.
Practise heat engines and heat pumps one question at a time
The player marks nothing for you. It shows one question, waits, then shows the scheme so you can mark yourself, and brings a question back sooner when it went badly.